Brantz Sensors

  • Brantz Dual Sensor Switch (BR49)

    Brantz Dual Sensor Switch (BR49)

    The Brantz Dual Sensor Switch is a handy piece of equipment that allows you to connect 2 sensors to one tripmeter, should the terrain change mid rally you can simply flick a switch to bring in to use the alternative sensor more appropriate to that...

    £32.05 inc. VAT
    £26.71 ex. VAT
    Add to Cart
  • Sensor Extension Cable (3M) (BR2X)

    Sensor Extension Cable (3M) (BR2X)

    The Brantz Sensor Extension Cable gives you that extra length for longer vehicles, or if the wiring is re-routed around the cars bodywork. Includes crimped ends for direct connection to your existing sensor cable and screw terminal blocks...

    £14.82 inc. VAT
    £12.35 ex. VAT
    Add to Cart
  • Brantz Pulse Doubler (BR52)

    Brantz Pulse Doubler (BR52)

    The Brantz Sensor Pulse Doubler is designed to be fitted to vehicles with a low number of pulses from the sensor producing a low calibration figure. A figure below 499 (or 999 on a Laser 3) can benefit in accuracy by adding a Pulse Doubler...

    £65.21 inc. VAT
    £54.34 ex. VAT
    Add to Cart
  • Brantz Pulse Reducer (BR5-2A)

    Brantz Pulse Reducer (BR5-2A)

    The Brantz Pulse Reducer is intended for use in conjunction with the Brantz Wheel Sensor (BR2A) when the number of pulses is too high for the calibration push-wheel digits on the tripmeter to compensate. SPECIFICATIONS:• to be Used in conjunction...

    £62.02 inc. VAT
    £51.68 ex. VAT
    Add to Cart
  • Brantz CANBUS Interface - Plug & Go (A-C) (BR58)

    Brantz CANBUS Interface - Plug & Go (A-C) (BR58)

    Most cars after 2005 have a CANBUS system. This is a multiplexed wiring system used to connect intelligent devices such as gearboxes and engine Electronic Controls Units (ECU's), Speed, ABS and Stereo information; allowing data to be transfered...

    £154.80 inc. VAT
    £129.00 ex. VAT
    Add to Cart
  • Brantz CANBUS Interface - Plug & Go (A-B) (BR57)

    Brantz CANBUS Interface - Plug & Go (A-B) (BR57)

    Most cars after 2005 have a CANBUS system. This is a multiplexed wiring system used to connect intelligent devices such as gearboxes and engine Electronic Controls Units (ECU's), Speed, ABS and Stereo information; allowing data to be transfered...

    £154.80 inc. VAT
    £129.00 ex. VAT
    Add to Cart
  • Brantz Contactless CANBUS Reader  Cable(BRCCR) Brantz Contactless CANBUS Reader  Cable(BRCCR)

    Brantz Contactless CANBUS Reader Cable(BRCCR)

    This contactless CANBUS reader works with the Brantz CANBUS Interface (BR56) to allow a non-intrusive connection (therefore not invalidating any warranty). It is excellent for the initial investigation period where you are trying to locate the correct...

    £64.80 inc. VAT
    £54.00 ex. VAT
    Add to Cart
  • Brantz CANBUS Interface (BR56)

    Brantz CANBUS Interface (BR56)

    The Brantz CANBUS Interface can be wired directly into your vehicles CANBUS System to obtain both a power source and the speed/distance information to be fed directly to the tripmeter.Compatible Vehicle List shown separately or contact Brantz for more...

    £154.80 inc. VAT
    £129.00 ex. VAT
    Add to Cart
  • Brantz Satellite Seeker (BRGPS)

    Brantz Satellite Seeker (BRGPS)

    This unit will convert any Brantz Tripmeter to a GNSS Trip. It calculates a superior three-dimensional ground speed/distance output with an integrated antenna. You can retro-fit to any Brantz using the wiring provided and place in the vehicle's...

    £217.80 inc. VAT
    £181.50 ex. VAT
    Add to Cart
  • Brantz Drive/Prop Shaft Sensor (BRH2)

    Brantz Drive/Prop Shaft Sensor (BRH2)

    Special sensor for generic detection of rotating shafts provide a bigger distance for the Brantz range of odometers. This type of sensor is ideal for particularly old (pre-war) cars or as a fall-back sensor to be utilised when the more easily implemented...

    £82.76 inc. VAT
    £68.97 ex. VAT
    Add to Cart